{"id":82,"date":"2025-01-10T17:30:49","date_gmt":"2025-01-10T17:30:49","guid":{"rendered":"https:\/\/urbanpicturehouse.com\/aftercare\/?page_id=82"},"modified":"2025-03-19T13:43:55","modified_gmt":"2025-03-19T13:43:55","slug":"2-13-smoke-and-heat-detectors","status":"publish","type":"page","link":"https:\/\/urbanpicturehouse.com\/aftercare\/2-0-new-home-information\/2-13-smoke-and-heat-detectors","title":{"rendered":"2.13<\/span> Smoke and Heat Detectors"},"content":{"rendered":"

Your home is protected by a smoke detector and a heat alarm. The units are hardwired to the mains electricity with a battery backup to ensure operation in the event of a power failure.<\/p>\n

There are four types of alarms installed throughout the development.<\/p>\n

In your apartment, you will have one of the following heat alarms:<\/p>\n

BG Mains Powered Heat Alarm<\/strong><\/p>\n

\"\"
\nInstructions<\/a> | Data Sheet<\/a><\/p>\n

 <\/p>\n

Aico Ei144e Heat Alarm<\/strong><\/p>\n

\"\"
\nInstructions<\/a> | Data Sheet<\/a><\/p>\n

<\/div>\n
and one of the following smoke alarms:<\/p>\n<\/div>\n
<\/div>\n
<\/div>\n
\n

BG Mains Powered Optical Smoke Alarm<\/strong><\/p>\n

\"\"
\nInstructions<\/a> | Data Sheet<\/a><\/p>\n<\/div>\n

 <\/p>\n

Aico Ei146e Optical Smoke Alarm<\/strong><\/p>\n

\"\"
\nInstructions<\/a> | Data Sheet<\/a><\/p>\n

Alarm Instructions and Maintenance<\/strong><\/h2>\n

The backup battery in your alarm is replaceable and should be a 9V alkaline or lithium battery, depending on the model. Only use the recommended battery type as specified in the instruction manuals above.<\/p>\n

The unit itself should be replaced approximately 10 years after installation. A small sticker on the outer casing indicates the replacement date.<\/p>\n

A small green indicator light (LED) should be visible through the detector grille, indicating that the alarm is receiving mains power. A red LED will flash every 40 to 50 seconds, to indicate normal operation or self-test status.<\/p>\n

If smoke or heat is detected, the alarm will emit a loud pulsating alarm, and the red LED will flash rapidly until the air is clear.<\/p>\n

If the alarm sounds without any visible signs of smoke, heat, or fire, follow these steps:<\/p>\n

    \n
  1. \n
      \n
    1. Evacuate immediately and ensure everyone is in a safe place before investigating.<\/li>\n
    2. Check the entire property carefully in case there is a small fire smouldering somewhere.<\/li>\n
    3. Do not disconnect the alarm. If no fire is found, ventilate the room and press the hush button, if available, to temporarily silence the alarm for 10 minutes.<\/li>\n<\/ol>\n<\/li>\n<\/ol>\n

      Testing Your Alarm<\/strong><\/h2>\n

      Regular testing is recommended to ensure your alarm is functioning correctly. Some models automatically conduct weekly self-tests.<\/p>\n

      To manually test your alarm:<\/p>\n

        \n
      1. Press and hold the test button for approximately five to ten seconds.<\/li>\n
      2. A loud pulsating alarm should sound, and the red LED should flash.<\/li>\n
      3. The alarm will stop once the button is released.<\/li>\n<\/ol>\n

        For interconnected alarms, test each unit individually to confirm that all alarms in the system are triggered correctly.<\/p>\n

        Maintaining Your Alarm<\/strong><\/h2>\n

        To reduce false alarms, clean the detectors regularly, as dust buildup can affect performance.<\/p>\n